Edgecore Help Center > Edgecore SONiC
Announcement
Getting Started
- [Edgecore SONiC] Create users in SONiC
- Get authorization and download Enterprise SONiC Distribution by Edgecore
- [Edgecore SONiC] SONiC overview
- [Edgecore SONiC] Installation & Upgrade image
- [Edgecore SONiC] Username and Password
- [Edgecore SONiC] Reset default configuration
- [Edgecore SONiC] Config load
- [Edgecore SONiC] Management and front port IPv4/IPv6 Address
- [Edgecore SONiC] Backup/Restore configure
- [Edgecore SONiC] JSON format & /etc/sonic/config_db.json
- [Edgecore SONiC] Verify JSON format of /etc/sonic/config_db.json in SONiC
- [Edgecore SONiC] Warm Reboot & Fast Reboot
- [Edgecore SONiC] Reset Password if forget username and password
Interface, Cables, Optics and Transceivers
- [Edgecore SONiC] Switch Port Attributes
- [Edgecore SONiC] LAG (Link Aggregation)
- [Edgecore SONiC] Transceiver status and DDMI
- [Edgecore SONiC] MTU (Maximum Transmission Unit)
- [Edgecore SONiC] Counter(Port counter and L3 RIF counter)
- [Edgecore SONiC] Dynamic Port Breakout
Basic Configuration
- [Edgecore SONiC] ZTP (Zero Touch Provisioning)
- [Edgecore SONiC] NAT(Network Address Translation)
- [Edgecore SONiC] RADIUS for user Authentication
- [Edgecore SONiC] DHCPv6 Relay
- [Edgecore SONiC] VLAN & Inter-VLAN Routing
- [Edgecore SONiC] Sub-Interface
- [Edgecore SONiC] MAC address table and aging time
- [Edgecore SONiC] ACL (Access Control List)
- [Edgecore SONiC] Mirroring function
- [Edgecore SONiC] LLDP (Link Layer Discovery Protocol)
- [Edgecore SONiC] SNMP (Simple Network Management Protocol)
- [Edgecore SONiC] DHCP Relay
- [Edgecore SONiC] TACACS+ for user Authentication/Accounting/Authorization
- [Edgecore SONiC] DNS
- [Edgecore SONiC] NTP (Network Time Protocol)
- [Edgecore SONiC] Selective QinQ
- [Edgecore SONiC] SFLOW (sampled flow)
Debug and Troubleshooting
- [Edgecore SONiC] Collectd
- [Edgecore SONiC] Hardware, Software and System Information
- [Edgecore SONiC] Tech-Support Dump
- [Edgecore SONiC] Syslog
Routing
- [Edgecore SONiC] FRRouting and config initialization
- [Edgecore SONiC] BGP Step 1 - Establish BGP Session
- [Edgecore SONiC] BGP Step 2 - Add the announcement network
- [Edgecore SONiC] BGP Step 2.1 Redistribute routes to BGP process (Optional)
- [Edgecore SONiC] BGP Unnumbered
- [Edgecore SONiC] VRF(Virtual routing and forwarding)
- [Edgecore SONiC] OSPF(Open Shortest Path First)
QoS (Quality of Service)
MCLAG
EVPN VxLAN
- [Edgecore SONiC] SAG(static anycast gateway)
- [Edgecore SONiC] EVPN L2 VxLAN
- [Edgecore SONiC] Symmetric EVPN IRB
- [Edgecore SONiC] Asymmetric EVPN IRB
- [Edgecore SONiC] EVPN ARP/ND Suppression
- [Edgecore SONiC] EVPN Multihoming
Technical Videos
- Getting Started - Download Edgecore SONiC and install it via ONIE
- Getting Started - Management of account and SONiC image
- Getting Started - Configuration file management
- Interfaces - Port Attributes
- Interfaces - Dynamic Port Breakout
- Interfaces - Link Aggregation Group
- Interfaces - Transceiver status and DDMI
- Basic Configuration - IP Address Assignment
- Basic Configuration - VLAN & Inter-VLAN Routing
- Advanced Setting - MC-LAG
- Advanced Setting - EVPN VxLAN
- Advanced Setting - EVPN Multihoming
- Advanced Setting - Static Anycast Gateway
Edgecore Help Center > Community
Enterprise Switch
- Wedge 100BF Ubuntu Installation Menu Garbled Screen Error / June 04, 2022 / Hussain Ahmad Mohammad
SONiC
- Port breakout not working / June 15, 2022 / Damien Saucez
- How can i change the p4 profile in ecSONIC-202111, WEDGE100QS? / November 23, 2022 19:33 / Seokwon Jang
Dear team, I'm using ecSONIC-202111-bfn-154 in wedge100QS. And i'm trying to test segment routing (SRv6), but ...
Edgecore Help Center > Open Networking Switch
Wedge100BF-32X/65X Troubleshooting Guide
- [Wedge100BF-series] cp2112 Error
- [Wedge100BF-series] Chip, OpenBMC, CPLD, EC Code, BIOS, ONIE, SPI version checking
- [Wedge100BF-series] Console failure
- [Wedge100BF-series] Management Port failure
- [Wedge100BF-series] MAC not found
- [Wedge100BF-series] QSFP can't link-up
- [Wedge100BF-series] PSU
- [Wedge100BF-series] FAN
- [Wedge100BF-series] Thermal Control Policy with Fan
Barefoot
Edgecore FAQ
- Q01 [Wedge100BF-series] OpenBMC upgrade procedures
- Q13 How to check Wedge100BF hardware information under OpenBMC?